MODIFICATION OF TYRE MACHINE SYSTEM WITH MITSUBISHI PLC AUTOMATIC FOOT LENGTH GAUGE

Hayadi Hamuda; Taufik Iqbal Miftaks; Lailatun Adzimah; Encik Yoega Renaldi; Muhammad Riza Syahputra; Novia Permata Atmadja

doi:10.62567/micjo.v3i1.1919

Authors

Hayadi Hamuda Pamulang University
Taufik Iqbal Miftaks Pamulang University
Lailatun Adzimah Pamulang University
Encik Yoega Renaldi Pamulang University
Muhammad Riza Syahputra Pamulang University
Novia Permata Atmadja Pamulang University

DOI:

https://doi.org/10.62567/micjo.v3i1.1919

Keywords:

HMI, Mitsubishi PLC, Operator, Rotary Encoder

Abstract

One of the steps in the tyre manufacturing process is the Tyre Building Machine. The tread is the last component to be fitted to the tyre carcass after all other components have been installed. When measuring the length of the pre-adjusted tread, errors or variations often occur in the measurements taken by the measuring device due to its lack of accuracy. This prevents operators from using the tyre tread and can result in a large amount of scrap and wasted time during the tyre manufacturing process. To overcome this problem, a redesigned tread length measurement system with a higher level of accuracy was created to minimise tread length fluctuations during tyre manufacturing. The results of the tread length measurement procedure using the ENC-1-1-24-N type rotary encoder can function according to the program created. This is validated by the tread length measurement data. The results of the HMI display design and the software created can operate according to the desired instructions. To change the tread length, the operator only needs to enter the number on the HMI panel.

Downloads

Download data is not yet available.

References

A. Goeritno, and S. Pratama (2020). "Design and Development of a Programmable Logic Controller-Based Control System Prototype for Miniature Material Sorting Operation." Journal of Electrical Engineering: vol. 16, no. 3, pp. 198-206.

Agus Supardi, Umar, Ilham Setiyoko, Muhammad Saifurrohman. (2022). "Design and Construction of an Induction Motor Speed Control System Based on a Programmable Logic Controller". EMITOR Journal of Electrical Engineering: Universitas Muhammadiyah Surakarta Vol. 22, No. 01. ISSN: 2541-4518.

Anis Hani Kurniawti, Arfa Mumtaza Ghalya, Ih-zam Fahraz Zikrullah, Nuha Nadhiroh, and Indra Z. (2022). "Motor Speed Control Based on Thermocouple Temperature Sensor in a PLC and SCADA-Based Battery Room Prototype." Jurnal PNJ: Politeknik Negeri Jakarta Vol. 4, No. 2. ISSN: 2686-5068.

Arif Kurniawan, Subuh Isnur Haryudo. (2024). "Design and Construction of a Single-Phase Automatic Transfer Switch (ATS) System Based on Outseal PLC Mega V.3 for Household Electrical Installations". Journal Of Telecommunication, Electronics, And Control Engineering (JTECE). Vol. 06, No. 02. ISSN: 2654-8275.

F. E. Ahmad and E. Fitriani, "Using the Outseal PLC System for Automatic Sorting and Automatic Counting," Bina Darma Conf. Eng. Sci., vol. 2, no. 2, pp. 27-39, (2020). Available: http://conference.binadarma.ac.id/index.php/BDCES.

H. Hendra, P. S, H. Hernadewita, H. Hermiyetti, and Y. Yoserizal, "Applying Programmable Logic Control (PLC) for Controlling Motors, Blowers, and Heaters in Rubber Drying Processing." J. Ilm. Tek. Elektro Komput. dan Inform., vol. 7, no. 1, p. 131, (2021), doi: 10.26555/jiteki.v7i1.20514.

I. M. Sitanggang, M. Sc, and I. L. Siregar, "Automatic Transfer Switch Using PLC Application at PT RHB," Electr. Power, Telecommun. Control Syst.- ELPOTECS J., vol. 4, no. 1, pp. 32-37, (2021).

Matthew Oluwole Arowolo, Adefemi Adeyemi Adekunle, and Martins Oluwaseun Opeyemi. (2020). "Design and Implementation of a PLC Trainer Workstation." Advances in Science, Technology and Engineering Systems. Journal Vol. 5, No. 4. ISSN: 2415-6698.

Muhammad Dafa Dezan Rezaputra, Muhammad Ridwan Arif Cahyono. (2021). "Design of an Automatic Press Roll Control System Based on Mitsubishi Type-Q PLC for Building Tire Machines". INAJET Journal: Indonesian Journal of Engineering and Technology Vol. 3, No. 2. e-ISSN: 2623-2464.

O. Saputra, "Outseal PLC Communication with Smartphone," Ranah Res. J. Multidiscip. Res. Dev., vol. 4, no. 4, pp. 310–325, (2022), doi: 10.38035/rrj.v4i4.539.

Riyandar, M. Wildan, A. Goeritno, J. Irawan (2021). "Development of a PLC-Based Embedded Device for a Rejection System Simulator with the Addition of a Human Machine Interface." Jurnal RESTI (Rekayasa Sistem dan Teknologi Informasi) Vol. 5 No. 6.

Saputra, T. H. and Hendriarto, C. (2020). "Design and Construction of an Automatic PLC-Based Water Press Assy Machine." Journal of Applied Smart Electrical Network and System (JASENS), 1(2), pp. 1–4. doi: https://doi.org/10.52158/jasens.v1i02.126.

S. Ardi, S. Fairus, V. K. Putri, "Automation Systems for the Regeneration Process of Demineralized Water to Maintain Quality Control using a Programmable Logic Controller." Proceedings of the 5th International Conference on Global Resource Conservation, Malang, (2019).

Sinka Wilyanti, Mauludi Manfaluhty, and Karseno. (2019). "Conveyor Control System for Counting Products Based on Programmable Logic Controller." Journal of Engineering: Muhammadiyah University of Tangerang (IRJET) Vol. 9, No. 2. P-ISSN: 2302-8734 EISSN 2581-0006.

Sumardi Sadi. (2020). "Implementation of Human Machine Interface on Programmable Logic Controller-Based Chin Ei Heel Lasting Machine." Journal of Engineering: Universitas Muhammadiyah Tangerang (IRJET) Vol. 9, No. 1. ISSN: 2581-0006.

Syahril Ardi, Sirin Fairus, and Sekar Sukmaningrum. (2020). "Design of a Control and Monitoring System for the Boiler Wastewater Treatment Process Using a Programmable Logic Controller and HMI (Human-Machine Interface)". Mechatronics Department, Astra Manufacturing Polytechnic, Astra International Complex, Jakarta. SINERGI Vol. 24, No. 2, June 2020: 133-140.

Wendhi Yuniarto, Mohd. Ilyas Hadikusuma, and Agus Riyanto. (2020). "Prototype of a Product Sorting Device Using PLC-Based Rotation Method - Electro Pneumatics." Elite Journal: Electrotechnics and Information Technology. Vol. 1, No. 2. P-ISSN: 2721-5636 EISSN 2721-5644.